Tuesday, January 10, 2012

Canon Canonet QL17 Re-Assembly

The shutter blades and the aperture leaves have been cleaned and put back to the shutter and they are now working fine.
Canonet QL Shutter test 

Wednesday, January 4, 2012

Canon Canonet QL17

I found a real junky looking Canon Canonet QL 17.
It has damaged top cover with meter not working, and shutter not running condition. I am going to try and restore this camera.
The camera seemed to have been dropped and landed on the top cover, destroying the accessory shoe, view finder glass, and shutter release button. I will find another parts camera and replace the top cover.

The meter problem was the meter display needle connected to the meter needle was pushed down from the impact. By bending it back fixed the meter movement.


When I opened the bottom cover, I saw a very deep battery holder to use no longer available 1.3v battery that I have never seen before. I thought QL17 used the same battery holder as OL19 that I worked on before. I have to figure out what to do about it after I work on the shutter.

Canon QL17 ( not smaller GIII model) uses Copal SV shutter. It is almost the same shutter that is used on the Konica Auto S2. The back side is different but looks similar to Konica Auto S than Auto S2.


Since, the shutter blades are not opening, I decided to do take them apart to do complete cleaning.

Here you see the shutter blades, and shutter control ring out from the shutter for cleaning. I only found three smaller shutter blades. I found 6 blades. Where is the extra blade come from?  I am not sure if this camera had been worked on before. I am going to put the blades back like the way they are used on Konica Auto S2.

Tomorrow, I am going to try to make the shutter working again. The parts camera should be arriving next week.

Monday, December 5, 2011

Konica Auto S2 Nov 2011 Replaced Parts

The parts needed replacing on this camera were the slow speed governor, battery holder box, and galvanometer.



The repairs needed was the finder glass.
The delay action escapement was cleaned and the light shield replaced and meter adjusted for 1.5 volt battery use.
The camera is for sale now at eBay.
The camera case looks very nice on this camera and the camera looks very nice too.

Thursday, November 17, 2011

Konica Auto S2 Nov 2011 Camera Case

I think it is official. The styrofoam used on the top side deteriorates over time on this case. It is now about half a century old. I am amazed the case lasted this long. The leather is still good and the case overall looks better than average.
I am going to be putting "new" styrofoam.  The best recycle material I found in my house was the styroform where you get your eggs from the stores. 2 dozen size is I am going to use. I can make two parts from the top cover. I will be going to Homedepot to buy the Amazing Goo glue. I think that glue should be safe to use on the styroform.


Konica Auto S2 Nov 2011

I am starting on the new project. This time it is going to be Konica Auto S2 with box. The box was bad condition but still functional so I made it more pleasing to the eyes. The green tomatoes are from my last crops. They are just sun bathing outside. Not turning red but going bad :) The camera looks very clean. It needs little service and be going up over the internet for sale after it is finished.

Tuesday, October 18, 2011

Canon Canonet QL19 Finished

Canon Canonet QL19 is finished and ready to be sold online.

Monday, October 17, 2011

Canon Canonet QL19 Auto Exposure

Canon QL19 and QL25 use trap needle for shutter priority auto exposure. The metered manual can also be used. Konica Auto S2 is another trap needle shutter priority auto exposure camera. Konica Auto S2's trap needle mechanism is more complicated. They are all mechanical which something I like over electronic cameras.The meter needle is used for opening the right f stop opening.
The aperture priority camera from this period used electronics. The most famous one is Yashica Electro 35. I will post this repairs later on.